- HOME >
- Application System >
- Laser Processing >
- Power Supply for LD Driving (CW or pulse output)
This is the power supply (supporting CW and pulse) for driving the laser diode (LD). The power supply for
driving a Peltier element and cooling unit all-in-one type required for driving LD is also part of our lineup.
LD Terminal Short Function
Function to short between anode and cathode of LD when power is switched OFF is equipped. By doing it,LD can be protected from static electricity, etc.
Goggle compatible white display
Letters can be displayed in white. Superior in legibility even when using laser-protect goggle.
Instantaneous power failure detection
LD can be safely protected by shutdown operation after instantaneous power failure detection, while there is electric current running after power has been cut off.
Various Alarm Functions
Alarm with screen display equipped enables prompt identification of cause and repair.
LD operation intergrator
LD operation intergrator function equipped, which is essential for LD lifecycle management.Zero reset available for LD replacement.
Full Interface
Interface equipped for setting in a system. Freely externally operable.
Simple Operation
Electric current limit setting and integrated time check can be done from a handle.
Electric current limit settings
Maximum electric current can be set in parameter. It prevents LD damage deriving from malfunction.
Precise digital control and high efficiency power supply for laser diodes
Voltage | 4V | |
Output current | 60A (Duty100%) | |
Output current (pulse) | 120A (Duty<50%, pulse width<10ms) | |
Current ripple | <120mA (rms) | |
Startup time | <20μs (rms) | |
Resolution of setting current | 0.1A | |
Frequency | 1Hz - 50kHz | |
Digits of setting frequency | 3 digits | |
Minimum setting pulse width | 0.01ms | |
Minimum setting duty | 0.01% | |
Wave shape | Rectangular or arbitrary (30 steps) | |
Start emission trigger | Internally set or external input | |
Hour meter | Emission time | |
Output of current monitor | 0 − 10V DC | |
Operation temperature | 0℃ - 40℃ | |
Storage temperature | -20℃ - 60℃ | |
Humidity | 20 - 90%RH (No condensation) | |
External dimensions | (W)250× (H)140× (D)330mm (Excluding projections) | |
Interface |
RS232C, emergency stop input, current out enable input etc. |
|
Accessories | Jumper connector, AC100V cable | |
Control mode |
CW | Output a set constant or continuous current |
PULSE |
Output a pulse current of set current and pulse width (or frequency) |
|
WAVE | Output an arbitrary wave (set up to 30 steps) | |
Control method |
FRONT PANEL | All control modes are available only from the front panel |
SERIAL I/F |
All control modes are available only with RS232C (serial communications) |
|
ANALOG | The output current is set by the voltage of the SIGNAL IN. | |
MOD | The output frequency is set by the frequency of the EXT MOD | |
GATE | Control emission on or off with GATE input. | |
Monitor output signal |
SYNC OUT | The current frequency is output to SYNC OUT as a pulse. |
CURRENT MONITOR |
The current is output to CURRENT MONITOR as a voltage. | |
Protection function |
Power abnormal, Inside temperature abnormal, output open, External power voltage drop etc. |
|
Fail-safe | Emergence stop,output permission key switch |
Designed specifically to diode power Diode.
Pulse or CW diodes can be driven.
Includes various function to protect LD.
Includes alarms such as instantaneous power failure.
Fine resolution closed loop current control.
Arbitrary wave output is available. (30 steps)
Output can be carried out with an output input signal only.
Bias control function for setting idle current.
Part Number | JP Yen | Add to Cart |
SMD0460P | 550,000 |
which are not shown in the catalog.
Please contact our sales department.